Fast, Reliable Heating & Furnace Across Alamo
Furnace repair in Alamo typically runs $150–$700 for standard fixes, with most calls completed same-day. Replacement systems start around $4,500 installed, though final cost depends on your home’s square footage and whether Contra Costa County permitting is involved.
We’re Redwood Heating & Air, and we’ve been driving out to Alamo since 2012. Gregory Hahn founded this company and still leads every technical decision, which means when you call (844) 875-9451, you’re talking to a Master Technician who will actually show up, not a dispatcher sending whoever’s available. We know the long service drives off Livorna Road, the acreage properties with detached workshops, and the specific headaches that come with 1980s ranch homes built before anyone worried about zoning or energy efficiency. Alamo’s 94507 ZIP sits far enough inland that your furnace works harder than systems ten miles west, and that matters when we’re diagnosing why your heat exchanger cracked or your gas valve keeps failing.
Why Redwood Heating & Air San Diego Is Alamo’s Preferred Heating & Furnace Company
Our Heating & Furnace team has completed hundreds of jobs in Alamo over 13 years, from single-room fixes on Stone Valley Road to full replacements on multi-acre properties near the Las Trampas Ridge. 428 verified customer reviews averaging 4.6 stars back our work, and a significant share of those come from repeat Alamo clients who’ve referred us to neighbors.
Response time to Alamo averages 45–90 minutes depending on whether you’re near the Diablo Road corridor or back on the rural roads south of the golf course. We don’t subcontract to crews from Danville or San Ramon who might not know that Alamo is unincorporated, which means county permitting, not city hall. That local knowledge saves our clients days or weeks on replacement jobs.
Gregory Hahn holds a Master Technician designation, and that credential is on the truck when we pull into your driveway. We’ve diagnosed and repaired systems from nine major brands in Alamo homes, including Trane, Lennox, and Rheem units that original builders installed in the 1980s and 1990s.
Our Heating & Furnace Services in Alamo
Furnace Repair
Most Alamo furnace repairs we handle involve gas valve failures, ignitor problems, or control board issues in 15–25 year old systems. The Diablo winds that sweep through the San Ramon Valley each fall and spring push dust and debris through outdoor intakes, fouling sensors and causing intermittent flame failures. We stock common Lennox and Goodman parts for Alamo’s housing stock, so most repairs finish in one visit. Typical furnace repair in Alamo runs $150–$700.
Furnace Replacement
Alamo’s large 1960s–1990s homes, many 3,000–5,000+ square feet with original single-zone duct systems, often need more than a straight swap. We size replacements for actual load, accounting for the extremely hot unconditioned attics where your ducts run and whether you’ve added square footage the original system never handled. Because Alamo is unincorporated, all permits and inspections run through the Contra Costa County Building Department rather than a city hall, a detail that trips up contractors from neighboring incorporated cities and can quietly delay project timelines if county inspection scheduling isn’t booked early. We handle that paperwork upfront. Replacement systems typically start around $4,500 installed.
Furnace Tune-Up
A proper tune-up in Alamo means checking static pressure across ductwork that runs through 140°F+ attics in summer, inspecting heat exchangers for cracks accelerated by Diablo wind temperature swings, and calibrating gas pressure for the altitude and dry air of the San Ramon Valley. We recommend annual service before the first wind event, usually late September. Tune-ups run $80–$200.
Heat Exchanger Repair & Replacement
Cracked heat exchangers are the most serious failure we see in Alamo’s aging furnaces. The combination of oversized original equipment, restricted return airflow from decades of dust accumulation, and the thermal stress of Diablo wind events creates perfect conditions for metal fatigue. We arrived at a 1980s custom ranch off Livorna Road where the homeowner’s 20-year-old single-stage furnace was short-cycling on the 2.5-ton AC’s coil. The original oversized, heavy-duty garage doors on his detached workshop had been upgraded by a previous owner to insulated steel, but the furnace return was undersized for the added square footage. We replaced the system with a two-stage Carrier unit and added zoning to correct the hot upper floor issue, done in one trip. Heat exchanger work ranges from $800–$2,200 depending on whether repair or full replacement is viable.
Gas Valve Repair
Gas valves in Alamo furnaces fail from sediment in the supply line, thermal cycling stress, or incorrect pressure regulation. We test inlet and manifold pressure with digital manometers, never guess. On acreage properties with long service lines from the street, pressure drops can mimic valve failure, so we verify the full delivery path before recommending parts.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Alamo
We service your brand, whether it’s the Trane XV80 that came with your 1995 custom build, the Lennox Merit series in your ranch off Diablo Road, or the Goodman unit a previous owner installed in your workshop. Gregory Hahn is factory-trained or field-experienced across nine major HVAC brands: Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. For Alamo customers, that means we don’t try to sell you what we happen to stock. We diagnose the actual problem, source the correct part, and fix it. Our parts inventory covers the most common failures for Alamo’s housing age, so most brand-specific repairs don’t wait on shipping.
Common Heating & Furnace Problems We See in Alamo Homes
- Cracked heat exchangers from static pressure spikes. Original single-zone ducts from the 1980s run through extremely hot unconditioned attics, causing static pressure spikes during Diablo wind events that can crack heat exchangers. We test with combustion analyzers and visual borescope inspection.
- Uneven heating between main house and detached workshop. Acreage properties with detached workshops often have separate furnace units not tied into the main zone, leading to uneven heating if the system isn’t properly sized for both structures. We calculate combined load and verify duct capacity.
- Short-cycling on oversized equipment. Many Alamo homes have furnaces rated for far more BTU than the actual heat loss requires, especially after energy improvements. The system heats too fast, shuts off, and repeats, wasting gas and wearing components.
- Delayed replacements worsening exchanger damage. County permitting delays cause homeowners to defer replacement, allowing cracked heat exchangers to worsen over multiple seasons. We file Contra Costa County permits immediately upon approval to protect your timeline and safety.
Pricing for Heating & Furnace in Alamo, CA
| Service | Typical Range in Alamo |
|---|---|
| Furnace Repair | $150–$700 |
| Furnace Replacement | $4,500–$8,850 |
| Tune-Up | $80–$200 |
| Heat Exchanger Repair/Replacement | $800–$2,200 |
| Gas Valve Repair | $250–$650 |
What moves your job within these ranges? Three things: the age and accessibility of your system (1980s attics in Alamo are tight), whether county permitting is required for replacement work, and whether your home needs zoning or duct modifications to correct original design limitations. We provide upfront written estimates before any work begins. Call (844) 875-9451 for a free estimate.
We Also Serve Cities Near Alamo
Our service radius covers Saranap to the west, Moraga across the hills, Walnut Creek to the north, and Danville to the south. Each has different permitting requirements, housing ages, and climate exposures. We adjust our approach accordingly, because a furnace in Danville’s incorporated jurisdiction faces different inspection timelines than your unincorporated Alamo project.
Serving Alamo, CA — Our Local Coverage Area
We’re based in the Alamo area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs — Heating & Furnace in Alamo
Yes. Alamo furnace replacements require Contra Costa County Building Department permits and inspections, not city hall approval, which typically adds 3–7 business days compared to incorporated cities like Danville or San Ramon. We file county permits immediately upon your approval and schedule inspections in advance to prevent delays. Call (844) 875-9451 to discuss your replacement timeline.
The sudden temperature and humidity spikes from Diablo winds increase the thermal load on your system, and if your furnace is oversized or your return airflow is restricted, it heats too quickly and shuts off prematurely. This is especially common in Alamo’s 1980s multi-story custom builds with original single-zone ducts. We measure actual heat loss and static pressure to determine whether resizing, zoning, or duct modification is the right fix.
Yes. We regularly service separate furnace units on Alamo acreage properties, and we size our diagnosis for the combined load of both structures. Many workshop systems were added by previous owners without proper load calculation, leading to uneven performance. We’ll verify whether your workshop unit is properly specified and whether tying it to a zoned main system makes sense.
We install Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard, selecting based on your home’s requirements rather than our inventory. For Alamo’s large homes with hot attic duct runs, we often recommend two-stage or variable-speed systems that can handle the load without the short-cycling problems common to single-stage replacements. Call (844) 875-9451 for brand-specific recommendations and a free estimate.
Warning signs include soot buildup around burner compartments, a clicking sound after the blower shuts off, or a CO detector alarm, any of which requires immediate professional inspection. In Alamo’s housing stock, cracked exchangers are accelerated by decades of static pressure stress from undersized returns and Diablo wind thermal cycling. We verify with combustion analysis and borescope inspection, never guess. If you suspect a crack, call (844) 875-9451 today, this is not a deferrable repair.
Written by Gregory Hahn, Owner at Redwood Heating & Air, serving Alamo and the San Ramon Valley since 2012.